αSTEP Battery-Free Built-In Absolute Encoder AZ Series
AZD-CD
Control Circuit
| การจำแนกประเภทผลิตภัณฑ์ | ชื่อผลิตภัณฑ์ | รายการราคา | วันที่จัดส่ง |
|---|---|---|---|
| Control Circuit | AZD-CD | THB 20,252 | 10 Working Days |
• Various data may be shown on the combination product page. Please check the page of the combination product.
รวม
- Control Circuit: Main Power Supply/Regeneration Resistor Connector (CN4), I/O Signal Connector (CN5), Connector for 24 VDC Power Supply input·Electromagnetic Brake Connector·Regeneration Unit Thermal Input·power removal signal input (CN1), Connector Wiring Lever
ข้อมูลเฉพาะ
ขนาด
Control Circuit
ดาวน์โหลดข้อมูล
ข้อมูลเฉพาะอื่น ๆ
Driver Specifications
| Driver Product Name | AZD-AD, AZD-CD | AZD-AM3, AZD-CM3 AZD-AS3, AZD-CS3 |
AZD-AEP, AZD-CEP AZD-AED, AZD-CED AZD-APN, AZD-CPN AZD-AX, AZD-CX AZD-A, AZD-C |
|
|---|---|---|---|---|
| Interface |
Pulse Input | － | － |
|
| Control Input | 10 Points Photocoupler |
4 Points Photocoupler |
6 Points Photocoupler |
|
| Pulse output | 2 Points Line Driver |
－ | 2 Points Line Driver |
|
| Control output | 6 Points Photocoupler and Open-Collector |
3 Points Photocoupler and Open-Collector |
6 Points Photocoupler and Open-Collector |
|
| Power Shut Down Input Signals |
2 Points Photocoupler |
|||
| Power Shut Down Monitor Output |
1 Point Photocoupler and Open-Collector |
|||
Driver function
| Built-In Controller Type |
Pulse input type with RS-485 communication |
Pulse Input Type |
EtherNet/IP compatible PROFINET Compatible |
||||
|---|---|---|---|---|---|---|---|
| Number of Positioning Data Sets | 256 Points | 256 Points*1 | 256 Points | ||||
| Remote I/O | Input | 16 Points | - | 16 Points | |||
| Output | 16 Points | - | 16 Points | ||||
| Setting Tool | Support Software MEXE02 | ||||||
| Coordinates Management Method | Battery-free Absolute System | ||||||
| Operation | Positioning Operation | Product Line | Positioning Operation | ○ | ○ | ○*1 | ○ |
| Positioning Push-Motion Operation*2 |
○ | ○ | ○*1 | ○ | |||
| Fastening method | Single-motion Operation | ○ | ○ | ○*1 | ○ | ||
| Sequential Operation | ○ | ○ | ○*1 | ○ | |||
| Multistep Speed-Change (Configuration connection) |
○ | ○ | ○*1 | ○ | |||
| Sequence control | Loop Operation (Repeating) |
○ | ○ | ○*1 | ○ | ||
| Event Jump Operation | ○ | ○ | ○*1 | ○ | |||
| Speed Control Operation (Continuous operation) | ○ | ○ | ○*1 | ○ | |||
| Return-To-Home Operation | Return-To-Home Operation | ○ | ○ | ○ | ○ | ||
| High-speed return-to-home operation | ○ | ○ | ○ | ○ | |||
| JOG Operation | ○ | ○ | ○ | ○ | |||
| Monitor/Information | Waveform Monitoring | ○ | ○ | ○ | ○ | ||
| Overload Detection | ○ | ○ | ○ | ○ | |||
| Overheat Detection (Motor and Driver) |
○ | ○ | ○ | ○ | |||
| Position/Speed Information | ○ | ○ | ○ | ○ | |||
| Temperature Detection (Motor and Driver) |
○ | ○ | ○ | ○ | |||
| Motor Load Factor | ○ | ○ | ○ | ○ | |||
| Travel Distance , Cumulative Travel Distance | ○ | ○ | ○ | ○ | |||
| Alarm | ○ | ○ | ○ | ○ | |||
- *1
- It can be used by setting it with the MEXE02 support software.
- *2
- Push-motion operation is not available for the geared motor and electric actuator DGII Series.
RS-485 Communication Specifications
| Protocol | Modbus RTU Mode |
|---|---|
| Electrical Characteristics | EIA-485 Compliant, Straight Cable Use twisted-pair cables (TIA/EIA-568B CAT5e or better recommended). The max. total extension length is 50 m.* |
| Mode | Half duplex communication and asynchronous mode (data: 8 bits, stop bit: 1 bit or 2 bits, parity: none, even, or odd) |
| Transmission Rate | 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, and 230400 bps are available. |
| Connection Type | Up to 31 units can be connected to a single programmable controller (master device). |
- *If a specific wiring and layout causes the motor cable or power supply cable to generate a noise problem, shield the cable or use ferrite cores.
Driver General Specifications
| Item | Specifications | |
|---|---|---|
| Operating Environment (In operation) | Ambient Temperature | 0 to +55 °C (Non-freezing)* |
| Ambient Humidity | 85 % max. (Non-condensing) | |
| Atmosphere | No corrosive gases or dust. No exposure to water, oil or other liquids. | |
- *When installing a heat sink equivalent to an aluminum plate min. 200 × 200 mm, thickness 2 mm
มาตรฐาน
Regulations and Standards Materials
Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)
Explanations of the Global Laws, Regulations and Standards can be found here.
Information about our compliance with regulations and standards for each of our product series can be found here.
Hazardous Substances
The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).
การกำหนดค่าระบบ
สายเคเบิลและอุปกรณ์เสริม
close